Specifications
Â
|
3 Year Warranty |
 |
Approvals:Â Â |
Â
|
Single Output |
|
Product No. |
Setting Voltage Range (Factory setting, canât be adjusted) |
Output Current (Based on the output volt.) |
Max Output Power |
Typ. Ripple & Noise |
Total Regulation |
Typ. Efficiency |
Typ.  |
Hold-Up Time |
Protection Mode |
||
|
min |
max |
min |
max |
||||||||
|
(VDC) |
(VDC) |
(A) |
(A) |
(W) |
(mVp-p) |
(%) |
(%) |
(W) |
(ms) |
||
|
SHFA32-102 |
5.0 |
6.0 |
3.33 |
4.00 |
20 |
50 |
±5 |
74 |
0.5 |
12 |
Hiccup |
|
SHFA32-S03 |
6.0 |
8.0 |
2.87 |
3.83 |
23 |
70 |
±5 |
77 |
0.5 |
12 |
Hiccup |
|
SHFA32-S04 |
8.0 |
11.0 |
2.45 |
3.37 |
27 |
90 |
±5 |
78 |
0.5 |
12 |
Hiccup |
|
SHFA32-S05 |
11.0 |
13.0 |
2.31 |
2.72 |
30 |
100 |
±5 |
83 |
0.5 |
12 |
Hiccup |
|
SHFA32-S06 |
13.0 |
16.0 |
1.88 |
2.31 |
30 |
100 |
±5 |
84 |
0.5 |
12 |
Hiccup |
|
SHFA32-S07 |
16.0 |
21.0 |
1.43 |
1.88 |
30 |
100 |
±5 |
85 |
0.5 |
12 |
Hiccup |
|
SHFA32-S08 |
21.0 |
27.0 |
1.12 |
1.43 |
30 |
100 |
±3 |
86 |
0.5 |
12 |
Hiccup |
|
SHFA32-S09 |
27.0 |
33.0 |
0.91 |
1.12 |
30 |
100 |
±3 |
86 |
0.5 |
12 |
Hiccup |
|
SHFA32-S10 |
33.0 |
40.0 |
0.76 |
0.91 |
30 |
100 |
±3 |
86 |
0.5 |
12 |
Hiccup |
Â
|
Electrical Characteristics |
|||||
|
Parameter |
Test Conditions |
Min. |
Typ. |
Max. |
Unit |
|
Safety Approvals Input Voltage Range |
Safety Approval & Specification in Label |
100 |
 |
240 |
VAC |
|
Operate Voltage Range |
Derate linearly from 100% load at 90VAC to 80% load at 80VAC |
80 |
 |
275 |
VAC |
|
Input Frequency |
Sine wave |
47 |
 |
63 |
Hz |
|
Output Power Range |
See Rating Chart |
 |
 |
30 |
W |
|
Low Line Input Current |
Full load, Vin=100VAC |
 |
 |
0.8 |
A |
|
High Line Input Current |
Full load, Vin=240VAC |
 |
 |
0.4 |
A |
|
Low Line Input Inrush Current |
Full load, 25°C, Cool start, Vin=100VAC |
 |
 |
25 |
A |
|
High Line Input Inrush Current |
Full load, 25°C, Cool start, Vin=240VAC |
 |
 |
50 |
A |
|
Efficiency |
Full Load, Vin=230VAC |
74 |
 |
86 |
% |
|
Line Regulation |
Full Load, Vin=100~120VAC or 200~240VAC |
 |
 |
1 |
% |
|
Over Load Protection |
Recovers automatically after fault condition is removed |
110 |
 |
150 |
% |
|
Time of Transient Response |
Io=Full Load to Half Load, Vin=110VAC |
 |
 |
4 |
ms |
|
Hold-Up Time |
Full Load, Vin=110VAC |
 |
 |
12 |
ms |
|
Start Up Time |
Full Load, Vin=100~240VAC |
 |
 |
0.5 |
s |
|
Insulation Resistance |
 |
50 |
 |
 |
MΩ |
|
Ripple & Noise (Peak to Peak) |
 |
 |
 |
1 |
% |
|
Temperature Coefficient |
All output |
 |
 |
±0.04 |
%/°C |
|
Dielectric Withstanding Voltage(P-S) |
Primary to Secondary, limit current<10mA |
 |
 |
4000 |
VAC |
|
EMC Emission |
Compliance to EN55011(CISPR11), EN60601-1-2 |
B |
 |
 |
Class |
Â
Â
Â
|
Environmental |
|||||
|
Parameter |
Test Conditions |
Min. |
Typ. |
Max. |
Unit |
|
Operating Temperature |
Derate linearly from 100% load at 40â to 50% load at 70â |
-10 |
 |
70 |
°C |
|
Storage Temperature |
10~95% RH |
-40 |
 |
85 |
°C |
|
Operating Humidity |
non-condensing |
0 |
 |
95% |
RH |
|
Storage Humidity |
 |
0 |
 |
95% |
RH |
|
Electro Static Discharge |
Air Discharge, IEC61000-4-2 |
 |
 |
15 |
KV |
|
Electro Static Discharge |
Contact Discharge, IEC61000-4-2 |
 |
 |
8 |
KV |
|
Mean Time Between Failure |
Operation Temperature at 25âJ, Calculated per MIL-HDBK-217F |
200K |
 |
 |
h |
|
Operating Altitude (Elevation) |
All Condition |
 |
 |
3000 |
m |
|
Vibration |
10~500Hz,10min./1cycle, 60min.each along X, Y, Z axes |
 |
 |
5 |
G |
|
Surge Voltage |
 Line-Neutral |
 |
 |
1 |
KV |
|
Surge Voltage |
 Line-PE & Neutral-PE |
 |
 |
2 |
KV |
Â
Â
|
Mechanical Drawing & Technical Chart |
   Â
|
|
PIN Chart:
  Note:
|
Â
|
Derating Curve |
|
|
1. Operating Temperature: -10 to 70°C 2. Derate linearly from 100% load at 50°C to 50% load at 70°C |
Â
