5 Year Warranty

Approvals:  

ELECTRICAL SPECIFICATIONS

PROTECTIONS & CONDITIONS

PROTECTION

OVER CURRENT Note.4

95 ~ 108%

Protection type: Constant current limiting, recovers automatically after fault condition is removed

SHORT CURRENT

Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

185V

123V

104V

100V

62V

54V

47V

Protection type: Hiccup mode, recovers automatically after fault condition is removed

OVER TEMP.

Hiccup mode, recovers automatically after fault condition is removed

ENVIRONMENT

WORKING TEMP.

-35 ~ +70℃ (Refer to “Derating Curve”)

WORKING HUMIDITY

10 ~ 100% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +85℃, 5 ~ 100% RH

TEMP. COEFFICIENT

±0.03%℃ (0~50℃)

VIBRATION

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY & EMC & GENERAL INFORMATION

SAFETY & EMC

SATETY STANDARDS Note.6

Meet UL8750, UL935, UL1012, CSA-C22.2 No.107.1, EN61347-1, EN61347-2-13

WITHSTAND VOLTAGE

I/P – O/P: 3.75kVAC,I/P-FG：2KVAC

ISOLTATION RESISTANCE

I/P – O/P: 100M Ohms / 500VDC /25℃ / 70% RH

EMC EMISSION

Compliance to EN55015, EN61000-3-2 Class C (≥60% load); EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level (surge 2kV), criteria A

OTHERS

MTBF

314khrs min.   MIL-HDBK-217F (25℃)

DIMENSIION

124(150)*68*42MM(L*W*H)

PACKING

715±10g

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance: includes set up tolerance, line regulation & load regulation.
4. Please refer to “DRIVING METHODS OF LED MODULE”.
5. Derating may be needed under low input voltages. Please check the static characteristics for details.
6. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes.
7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacture must re-qualify EMC DIRECTIVE on the complete installation again.
9. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
10. To fulfill requirements of the latest ERP regulation for lighting fixtures, this LED power supply can only be used behind switch without permanently connected to the mains.

MECHANICAL SPECIFICATION

JLPA120JU SERIES NO Dimming Function Mechanical

JLPA120JUD SERIES Dimming Function Mechanical

DERATING CURVE

DIMMING FUNCTION

 0-10V Analog Dimming

1:Positive logic

2:Negative logic

NOTE:

1. If the dimming function is not used, all wire NC.

2. Io is actual output current and Ir is rated current without dimming control.

3. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like resistors and Zener.

4. The dimming signal is allowed to be less than 1V, when it for 0-1V, the connected LEDs may flicker. Keeping dimming voltage

greater than 1V in application is strongly recommended.

5. Do not connect the GND of DIM-(gray) to the output. Otherwise, the LED driver can not work normally.

 0-5V Analog Dimming

1:Positive logic

2:Negative logic

NOTE:

1.If the dimming function is not used, all wire NC.

2. Io is actual output current and Ir is rated current without dimming control.

3. The dimmer can also be replaced by an active 0-5V voltage source signal or passive resistors and Zener.

4. Do not connect the GND of DIM-(gray) to the output. Otherwise, the LED driver can not work normally.