JLPA75JU(D) SERIES


75W Single Output Constant Current LED Driver


  • Wide Input Voltage 90 to 305VAC, 47 to 63Hz
  • Over Voltage / Short Circuit / Over Temperature Protection
  • High Efficiency (up to 90%), Active Power Factor Correction (PFC)
  • IP67 Waterproof Rating, Fully isolated 
  • Selectable dimming function ( 0~5V / 0~10V )
  • Cooling by free air convection
  • Input Surge Protection:4KV line-line¡A6KV line-PE

Specifications

 

 

5 Year Warranty

 

Approvals:  

 

ELECTRICAL SPECIFICATIONS

PART NUMBER

JLPA75JU(D)-

S0700S

JLPA75JU(D)-

S1050S

JLPA75JU(D)-

S1400S

JLPA75JU(D)-

S1750S

JLPA75JU(D)-

S2100S

OUTPUT

DC VOLTiaAGE

64-107V

43 -71V

32-54V

26-43V

21-36V

CONSTANT CURRENT REGION Note.1

700mA

1050mA

1400mA

1750mA

2100mA

RATED POWER

75W

RIPPLE & NOISE(max.) Note.2

3.2V

2.1V

1.6V

1.3V

1.0V

CURRENT TOLERANCE Note.3

±5.0%

LINE REGULATION

±2.0%

LOAD REGULATION

±3.0%

SETUP, RISE TIME(Typ.) Note.7

1500ms/50ms 115VAC at full load       500ms/50ms 230VAC

INPUT

VOLTAGE RANGE Note.5

90 ~305VAC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACTOR(Typ.)

0.99@115VAC 60HZ  0.96@230VAC 50HZ

EFFICIENCY(Typ.)

90%

89%

89%

88%

88%

AC CURRENT(Typ.)

0.91A/115VAC     0.42A/230VAC

INRUSH CURRENT(Typ.)

COLD START 50A ( Twidth=270us measured at 50% Ipeak ) at 230VAC

LEAKAGE CURRENT

<0.75mA/265VAC

 

PROTECTIONS & CONDITIONS

PROTECTION

OVER CURRENT Note.4

95 ~ 108%

Protection type: Constant current limiting, recovers automatically after fault condition is removed

SHORT CURRENT

Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

90V

63V

48V

39V

Protection type: Hiccup mode, recovers automatically after fault condition is removed

OVER TEMP.

Hiccup mode, recovers automatically after fault condition is removed

ENVIRONMENT

WORKING TEMP.

-35 ~ +70℃ (Refer to “Derating Curve”)

WORKING HUMIDITY

10 ~ 100% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +85℃, 5 ~ 100% RH

TEMP. COEFFICIENT

±0.03%℃ (0~50℃)

VIBRATION

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

 

 

SAFETY & EMC & GENERAL INFORMATION

SAFETY & EMC

SATETY STANDARDS Note.6

UL8750, UL935, UL1012, CSA-C22.2 No.107.1, EN61347-1, EN61347-2-13

WITHSTAND VOLTAGE

I/P – O/P: 3.75kVAC,I/P-FG2KVAC

ISOLTATION RESISTANCE

I/P – O/P: 100M Ohms / 500VDC /25℃ / 70% RH

EMC EMISSION

Compliance to EN55015, EN61000-3-2 Class C (≥60% load); EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level (surge 2kV), criteria A

OTHERS

MTBF

450khrs min.      MIL-HDBK-217F (25℃)

DIMENSIION

150(177)*65.5*39.5MM(L*W*H)

PACKING

745±10g

NOTE

  1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
  2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
  3. Tolerance: includes set up tolerance, line regulation & load regulation.
  4. Please refer to “DRIVING METHODS OF LED MODULE”.
  5. Derating may be needed under low input voltages. Please check the static characteristics for details.
  6. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes.
  7. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
  8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacture must re-qualify EMC DIRECTIVE on the complete installation again.
  9. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
  10. To fulfill requirements of the latest ERP regulation for lighting fixtures, this LED power supply can only be used behind switch without permanently connected to the mains.

 

 

MECHANICAL SPECIFICATION

JLPA75JU SERIES NO or TIMER Dimming Function Mechanical

 

 

MECHANICAL SPECIFICATION

JLPA75JUD SERIES  Dimming Function Mechanical

 

 

 

CHARACTERISTIC CHARTS

Derating Characteristics 

Static Characteristics

Power Factor Characters 
JLPA75JUD-S0700S

Power Factor Characters 
JLPA75JUD-S2100S

Efficiency vs Load

JLPA75JUD-S0700S

Efficiency vs Load

JLPA75JUD-S2100S

Life Time vs TA, TC

 

 

 

 

DIMMING FUNCTION

 0-10V Analog Dimming

1:Positive logic

2:Negative logic

DIMMING

 

 SPECIFICATIONS

12V AUXILIARY OUTPUT VOLTAGE

10.8-13.2V

12V AUXILIARY OUTPUT SOURCE CURRENT(MAX)

20mA

DIM+ PIN SOURCE CURRENT(MAX)

250uA

DIMMING INPUT RANG

0-10V

NOTE:

1. If the dimming function is not used, all wire NC.

2. Io is actual output current and Ir is rated current without dimming control.

3. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like resistors and Zener.

4. The dimming signal is allowed to be less than 1V, when it for 0-1V, the connected LEDs may flicker. Keeping dimming voltage

greater than 1V in application is strongly recommended.

5. Do not connect the GND of DIM-(gray) to the output. Otherwise, the LED driver can not work normally.

 

 

 0-5V Analog Dimming

1:Positive logic

2:Negative logic

DIMMING

 

 SPECIFICATIONS

12V AUXILIARY OUTPUT VOLTAGE

10.8-13.2V

12V AUXILIARY OUTPUT SOURCE CURRENT(MAX)

20mA

DIM+ PIN SOURCE CURRENT(MAX)

250uA

DIMMING INPUT RANG

0-5V

NOTE:

1.If the dimming function is not used, all wire NC.

2. Io is actual output current and Ir is rated current without dimming control.

3. The dimmer can also be replaced by an active 0-5V voltage source signal or passive resistors and Zener.

4. Do not connect the GND of DIM-(gray) to the output. Otherwise, the LED driver can not work normally.


 

 
JLPA75JU - MEPOS ELECTRONICS
English Danish Dutch French German Italian Japanese Lithuanian Norwegian Portuguese Spanish Swedish

Quotation

No items in cart