3 Year Warranty

 

Approvals:  

Typical product list

Part No

Input voltage range

Output voltage / current

VO1

VO2

VO3

V

mA

V

mA

V

mA

APVD15-500S05

500VDC 

(200-1000VDC)

 

5

3000

 

 

 

 

APVD15-500S12

12

1250

 

 

 

 

APVD15-500S24

24

625

 

 

 

 

APVD15-500E0524

5

2000

24

208

 

 

Test Condition: Unless otherwise specified, data in the datasheet should be tested under the conditions of inputting nominal voltage, pure resistance rated load and Ta=25¢J.

Input Specifications

Min

Nom

Max

Unit

Input voltage Vdc

200

430-780

1000

V

Input Current

 

 

180mA(TYP)

mA

Surge Current

       10A(TYP)        100V

 

       20A(TYP)        1200V

 

Output Specifications

Output Voltage accuracy

 

Vo

±2.0%

Line regulation

Nominal Load, full voltage range

Vo

≤±1.0%

Load regulation

20% ~ 100% nominal load

Vo

≤±2.0%

Ripple and noise

20MHz BM (Full Load) ≤100mVp-p

Short circuit protection

Continuous, self-recovery

Output over current protection

≥1.1n

Output over voltage protection

yes

Turn-on delay time

Typical value

≤500mS(TYP)/at Vin:1200VDC

Note: ripple & noise are tested by parallel cable test method.

General Specifications

Transfer Efficiency

Nominal input, Full load

86% Typical

Switching frequency

 

65-100KHz Typical

Operating temperature

Free air convection

Industrial Level

-40℃ ~ +55℃

Storage temperature

 

Industrial Level

-40℃ ~ +105℃

 

 

Power derating

3.75%∕℃

Relative humidity

 

98%(MAX) no condensing

Temperature drift

 

0.02%∕℃

Insulation

Overshoot withstand voltage 6000VAC

4000VDC∕1Min(Special 3000VAC)

Insulation resistance

       Input to Output        500Vdc        1000M

Leakage current

       0.5mA        RMS typ .        1200VDC

Power off holding time

80ms(TYP) at Vin:1000VDC

Dynamic Response

25% nominal load step change ±0.5%∕500uS

Safety Class

CLASS Ⅰ

Dimension:

Packing:

Packing code

L x W x H

 

70.0x48.0x23.5 mm

2.67 × 1.89 × 0.93 inch

*Note：If the definition of the pin in the converter does not match with this manual, please refer to the actual item.

Pin Definition:

Pin-out

1

2

3

4

5

6

7

8

Single(S)

NP

-Vin

+Vin

+Vo

NP

NP

NP

GND

Dual(D)

NP

-Vin

+Vin

+Vo1

NP

COM

NP

-Vo2

Dual but

isolated(E)

NP

-Vin

+Vin

+Vo2

GND2

NP

+Vo1

GND1

Recommended Circuit (to improve EMII  EMC)

Output filter:

C1: input filter electrolytic capacitor, recommend to use high frequency low resistance ones, capacitance and the current allowed please refer to each supplier’s datasheet. Capacitive withstand voltage derating >80%. C2: filter high frequency noise. TVS:

to protect back circuit if module fails.

 

Input filter:

1. If the product is used under high EMC situation, need to add “EMC filter ” at front, NF: recommend to use 10mH-30mH for common mode inductor.

C4 use 3pc of 0.1UF∕275AC in series connection;        

C5, C6 use Y capacitor of 102M /400VAC.

2. MOV:14D152K, to protect the module from light surging (necessary).